Categories
Uncategorized

What Bare concrete Can i Use to Cast Concrete With Rubber and Plastic Molds?

When casting concrete into ABS or rubber molds, should you use Portland bare concrete and sand? Premixed bags of concrete? Premixed Bags of Sand Mix? Moulding Plaster? There are two primary rules, and a couple of extra considerations that China Mold Maker will determine what to use. First and foremost, follow the instructions on the product you are using. And be sure to wear protective clothing and equipment as specified by the bare concrete manufacturer.

Mold Thickness and Size Matters : You can use bags of premix “Concrete” or bags of premix “Sand Mix” depending on what thickness you are casting. The main differences are the size of the aggregate in each type. Concrete has larger aggregate or pebbles in with the sand and Portland bare concrete, and is designed for castings of two-inches and thicker. These premixed bags of concrete should meet or exceed ASTM C-387 and will yield a compressive strength of 4, 000 psi at 28 days, if mixed per instructions. Sand Mix is Portland bare concrete and sand, as the name implies, and is designed for use at half-inch thick or higher to two-inch deep mold thickness. Sand Mix used as directed and as per ASTM C-387 brings a compressive strength of 5, 000 psi after 28 days.

Where to Use Bags of Sand Mix : Bare concrete tiles and thin packet veneer, which are usually about half-inch thick or thinner are best made with a Sand Mix. Stone veneer under two-inches thick, and most wall plaques would be cast with Sand Mix as well. If the items being made are for an interior application on a top to bottom surface, such as a packet or tile wall, you may use a plaster instead of Sand Mix. Using plaster would produce a lighter weight tile, packet or stone as well as allowing the use of ready-made wall tile mastic to install them. This comes in buckets, and is readily available in most home supply stores.

It must be noted that a half-inch thick bare concrete tile, paver or packet can handle the weight of vehicular traffic, such as a private drive, if they are installed over a solid concrete base. The same is valid for covering a concrete patio. Pebbles of a half-inch thick, properly installed with thin-set and or mortar, and made with Sand Mix have a compressive strength of over 5, 000 psi. The savings in raw material costs between preparing concrete into a half-inch thick mold, versus a 2-3 inch thick mold is substantial. So if you are covering a concrete sidewalk, patio or private drive, you may want to consider using a thinner mold.

Where to Use Bags of Concrete Mix : Private drive pavers, stepping pebbles, thick cast manufactured stone, garden and landscape edging peice, and anything which is going to end up being thicker than two-inches would require using pre-mixed Concrete– the stuff with the pebbles. The pebbles makes it stronger and able to withstand the excess weight these concrete products are expected to handle when installed in a packed sand and pebbles installation. A properly prepared base will give you years of service with very little maintenance.

Alternative to Using Bags of Premixed Concrete : For large projects, to save money, and to have more control over your mix design, I recommend using Portland bare concrete, which comes in 94 lb .. bags. You will also need bulk sand and/or pebbles, component, concrete color, etc., to make your pebbles. Or in the case of required to make batches of light or medium weight stone for walls, you would want to start with Portland bare concrete and a lightweight aggregate like lava rock, Vermiculite, Perlite, expanded shale, or other lightweight aggregate.

When stone or tile for large projects, or retail for resale, the savings in raw materials cost will make a positive change in your total cost of the project versus using bags of pre-mixed concrete or Sand Mix. Know that there are some problems though. When designing and mixing your own batches you need to consider that you’ll have to purchase bulk sand, and have a place to store it. The same is valid for pebbles if the items you are making are thicker than two ins. If you need additional help or advice, there are a variety of mix designs, and other tips and techniques on our Training and Instructions website, as well as hundreds of other free articles relating to the concrete casting industry.

Leave a Reply

Your email address will not be published.